Should i use a groove sharpener

Before you go shopping for a new set of irons, we may have a solution for worn-down grooves. There are distinctly manufactured groove sharpeners, and there are also plenty of DIY options. Golf clubs groove sharpeners definitely work.

Using a groove sharpener can give a golf club a little more grip on a golf ball. The friction between the club and the ball is necessary when trying to create spin. How do you know how to sharpen grooves on golf clubs? Each golf club groove sharper will come with specific instructions designed for that sharpener. There is a maximum depth and sharpness of grooves allowed by manufacturing standards.

There is no standard amount that you should sharpen your grooves. Tips On Using A Wedge Groove Sharpener With wedges, you will notice an even more drastic change in spin and accuracy when sharpening grooves. Go slow and steady, making sure you maintain the structural integrity of the original grooves. Use a good quality sharpener that fits the grooves of your wedge correctly. Ideas For A Homemade Groove Sharpener Although there are plenty of affordable options for professionally made groove sharpeners, it may not be necessary to buy one.

Using a flat head screwdriver is one of the most common DIY options out there. It is very unlikely that you will achieve such a significant increase in the ball angular momentum. The most you can get is another rpm. Do not slide your fingers over a sharpened club face even when clearing grass. Keep a thick cloth or a towel to do this now. While sharpening the grooves, the metal shards may get filled and stuck on the lining. Also, the lining itself will become sharp.

You can get cuts from just a slight slide. Even while cutting the grooves, the small metal particles can easily cut through your skin. If you plan to do this experiment, make sure that you have thick gloves and eye protector in place. A sharpened club head is not worth an injured eye or finger. Sharpened grooves will not add any significant spin on the ball but they can actually reduce if used on the same ball.

Golf ball aerodynamics are extremely important. By a strong impact with razor sharps, grooves can scuff the ball outer covering. As the ball goes into the flight it will face the increased drag. It will decrease the spin induced on the ball. Balls such as superhot bold can survive the beating because of the relatively outer hard shell. The main point to remember is that the shape of a groove cannot be changed by the golfer. This is considered illegal.

So if you are careful to not change the shape, then you can definitely use a sharpener. You will need to refer to the tournament manual in detail before using a groove sharpener.

There are a lot of ideas that can be used to sharpen the grooves of your old wedges. A lot of golfers find that buying a proper grove sharpener is entirely unnecessary to help sharpen the wedges. A simple flat faced screwdriver could be used to sharpen the edges.

Some people have also used nail files to clean and sharpen the grooves. You might be able to make this work by using any tool which is the same size as the groove. As long as the tool is sharp enough and fits, then it should work. I recommend you attempt any homemade methods at least a few days before a golf game. A lot of people often wonder whether it is completely necessary to buy a groove sharpener. Many people have found that using some simple tools found at the house such as a screwdriver can help in doing the job.

A simple flat headed screwdriver can be used to sharpen the wedges. The screwdriver needs to be of a size suitable for the groove not too big or small. Carefully run them through the grooves. This can easily sharpen them without much effort.

The grooves might have become soft and faded a bit. You can either get the regrooving done by an expert company, or you can do it yourself.

If your grooves are clean and sharp, you instead may have scratches on the face of your club. See how I remove scratches and marks on my own clubs read my article. If you want to avoid the cost or hassle of sharpening your irons yourself, you can certainly use a regrooving service instead.

Any specialized golf shop that sells clubs will certainly offer this service. Using a restoration service will save you time and is normally very affordable to use.

If I compare them with the mack daddy 2's I had there is no spin at all. Ball lands and rolls across the green. IMO, groove sharpeners dont work because all they do is cut the grooves deeper.

If the shoulder of the grooves are still worn down and rounded off, thats not going to really help. What you really want to do is to CNC mill the face of the wedge, so that the shoulders of the grooves and sharp and square again, like when the club was new.

The USGA will remain clueless forever, it seems. All the rule changes are geared to tournament players when recreational players are the heart of the game.

They decided the old 1. They decided that playing with a complete set was too easy, so they came up with the fourteen-club rule. I love having to leave clubs that cost me three figures each in my locker when I play in a member-guest. They came up with the groove rule, but not because the box grooves were making the game too easy for us. Somehow, they allowed drivers to swell to a cartoonish cc, but when they realized their mistake, they established COR limits just not to admit that they were asleep at the wheel while somebody was impregnating the titanium drivers.

Finally, they set up the US Open venues so that a good, single digit club player couldn't break It's OUR game. Let the tour guys play at or yards so we can actually see how much better than us they are! As a boxing fan, I often lament the number of ridiculous, alphabet soup sanctioning bodies that have cheapened the sport. Golf seems to have the opposite problem.

I think that the USGA really needs a competitor. Badger said it. The face condition is the biggest factor. It's not like the ball squishes into grooves.

A milled face with no grooves would spin the ball more than with grooves on a clean strike. Once you try that in the rough though, it would slide up the face more and have very little spin. Yes groove sharpeners work for cleaning up the grooves, squaring them out and redoing the radius of the edges. Thing is, unless you use a gauge, they'll be out of tolerances and outside the rules.

The best one out there is the Golfsmith tool that looks like a screwdriver with replaceable heads. It'll do v and square groves. Material doesn't matter, just remember to tape off both ends of the score lines in case you slip with the tool. Bomb and gouge. Yes, I'm a club gigolo. RB7 opines that the type of steel doesn't matter. That's not my experience, but I wouldn't claim to be an expert on the subject.

Just try it, I guess. I have the exact same tool as Phil! I haven't used mine in a few years but I think it helped clean up some rounded shoulders, etc. I like messing around with clubs so it was kind of fun to do. Did my club performance improve?

Do I think it did? Will it hurt to try it out?